Keyboard Shortcuts

Master the workflow canvas with keyboard shortcuts and mouse controls

Speed up your workflow building with these keyboard shortcuts and mouse controls. SteelEngine ignores most shortcuts while you type in an input field. Mod + K, Mod + L, Mod + O, Mod + Shift + A, and Mod + Shift + Enter work everywhere.

Mod refers to Cmd on macOS and Ctrl on Windows/Linux.

Canvas Controls

Mouse Controls

The canvas starts in Mover mode. Switch between Mover and Pointer mode from the canvas controls in the bottom-left corner of the canvas.

ActionControl
Pan/move canvasLeft-drag on empty space (Mover mode)
Pan/move canvasScroll or trackpad
Select multiple blocksShift + drag to draw a selection box (left-drag in Pointer mode)
Drag blockLeft-drag on block header
Add to selectionMod + click or Shift + click on blocks

Wire Ties

A wire bundle gathers messy wires into one tidy path, so a busy canvas stays readable. Each bundle passes through one or more ties: short bars that hold the wires in parallel lanes. Ties are layout only: they never change how the workflow runs. They are saved with the workflow and shared with everyone who has it open, the same way block positions are. Running auto-layout removes every tie.

ActionControl
Bundle wiresHold Alt (Option on macOS) and drag a line across two or more wires
Bundle wires without the keyboardRight-click the canvas, choose Tidy wires into a bundle, then drag across the wires. Press Esc to cancel
Bundle the wires of every blockRight-click the canvas and choose Bundle wires from each block, or click the bundle button at the right end of the canvas toolbar
Add a second tie to a bundleAlt + drag across the same wires away from the existing tie
Move a tieDrag the tie bar, or Alt + drag a new line close to it
Select a tieClick the tie bar, or focus it with Tab and press Enter
Remove a tieSelect it and press Delete or Backspace, or click its ×
Select a fork's tieClick the shared trunk before the tie

The first few times you hover a wire, a small before-and-after picture shows how to make a bundle. It stops once you make one. Until then the bundle button in the canvas toolbar wears a small dot; the dot goes away when you click the button, when you make a bundle, or after two weeks.

When every wire in a bundle leaves the same output, the bundle draws as a fork: one trunk runs from the output to the tie, and the wires branch toward their targets after it. Hovering the trunk highlights every wire in the fork. Click a branch to select one wire.

When a block gets a second wire, the editor ties that block's wires for you. Wires from one output form a fork through one tie just before the nearest target. Wires from different outputs, such as a condition's branches, get two ties, one just after the block and one just before the targets, and run between them in parallel lanes. Wires from a block's error output get a tie of their own. Wires you add from that block later join the same tie. If you remove one of these ties, the editor does not make it again for that block, even after auto-layout. Bundle wires from each block brings it back and adds any tie the block is missing.

Where wires would bend along the same line, the canvas spreads them into parallel lanes so they never sit on top of each other.

A tie can hold up to 50 wires, and a workflow can hold up to 200 ties. Ties are not shown in diff view or on snapshots.

Wire Style

Wires draw in one of two styles. Smooth wires, the default, draw as taut cables that curve between blocks and run straight through each tie; smooth wires from one output leave it fanned apart so they never overlap. Right-angle wires run in straight lines with square corners. Click the wire style button in the wire group at the right end of the canvas toolbar, next to the bundle button, to switch. The wires ease into the new shape. The choice is yours alone: it is kept on your device and does not change the workflow for anyone else.

Workflow Actions

ShortcutAction
Mod + EnterRun workflow (or cancel if running)
Mod + ZUndo
Mod + Shift + ZRedo
Mod + CCopy selected blocks
Mod + VPaste blocks
Delete or BackspaceDelete selected blocks or edges
Shift + LAuto-layout canvas
Mod + Shift + FFit to view
Mod + Shift + EnterAccept Chat changes

Canvas Right-Click Menu

Right-click empty canvas space to open a menu with the most common actions.

ItemAction
Undo / RedoSame as Mod + Z and Mod + Shift + Z
PastePaste copied blocks (Mod + V)
Add BlockOpen search (Mod + K)
Auto-layoutAuto-layout the canvas (Shift + L)
Lock workflow / Unlock workflowLock or unlock every block (Admin only)
Fit to ViewFit all blocks in the viewport
Smooth wiresSwitch wires between smooth (the default) and right-angle. See Wire Style
Open LogsGo to the Logs page (Mod + L)
Open Variables / Close VariablesToggle the workflow Variables panel
Open Chat / Close ChatToggle the Chat panel used to test the workflow

Panel Navigation

These shortcuts switch between panel tabs on the right side of the canvas.

ShortcutAction
Mod + FFocus Toolbar search
ShortcutAction
Mod + KOpen search
Mod + OOpen or close the workspace switcher
Mod + Shift + PNew workflow
Mod + Shift + KNew chat
Mod + Shift + AAdd an Agent block to the canvas
Mod + LGo to logs

Workspace Switcher

While the workspace switcher is open, other shortcuts are paused so they can't act on the page behind it.

ShortcutAction
↑ / ↓Move through workspaces and organization headings
EnterOpen the highlighted workspace, or the highlighted organization's dashboard
← / →Collapse or expand the highlighted organization
Mod + ↑ / Mod + ↓Move the organization column's selection
Tab (in the search box)Switch between Your workspaces and Browse
Shift + F10Open the highlighted workspace's actions
EscClear the search, then the organization filter, then close
Mod + OClose

Utility

ShortcutAction
Mod + DClear terminal console
Mod + EClear notifications

On this page